Assessment of Conical Die Deep Drawability of DP800 and MART1400 Advanced High Strength Steels

Basit Öğe Kaydı
dc.authorscopusid56702042600en_US
dc.authorscopusid57280068600en_US
dc.authorscopusid58345584900en_US
dc.contributor.authorŞen, N.
dc.contributor.authorCivek, T.
dc.contributor.authorTongü, E.
dc.date.accessioned2024-08-23T16:07:28Z
dc.date.available2024-08-23T16:07:28Z
dc.date.issued2023en_US
dc.departmentDüzce Üniversitesien_US
dc.description.abstractDeep drawing is one of the most important and vastly conducted sheet metal forming method. Thus, even small improvements achieved on the deep drawability of sheet metals significantly increases the ability of sheet metal to be formed into more complex products. Advanced high strength steels (AHSSs) are one of the most popular steels in the automotive industry due to their high strengths. However, their low ductility causes considerable splitting problems near the cup punch region. In this study, deep drawing experiments have been conducted in conical dies with four different angles (0°, 7.5°, 12.5°, and 20°) for DP800 and MART 1400 steels to observe whether a higher deep drawing ratio (DDR) can be achieved by deep drawing in conical dies for AHSSs. In addition, finite element analysis (FEA) has been utilized to estimate the DDR for each types of steels in different conical die setups. It has been observed that the deep drawability of MART1400 steel has not improved in any of the conical die setups. However, DDR of DP800 has slightly increased by 2.46% by deep drawing with 20° die angle. A good agreement with the numerical and experimental results has been achieved. © 2023 Universidade do Vale do Rio dos Sinos. All rights reserved.en_US
dc.description.sponsorshipDüzce Üniversitesi, (2020.06.05.1113)en_US
dc.identifier.doi10.30939/ijastech..1278573
dc.identifier.endpage111en_US
dc.identifier.issn2587-0963
dc.identifier.issue2en_US
dc.identifier.scopus2-s2.0-85162836361en_US
dc.identifier.scopusqualityN/Aen_US
dc.identifier.startpage104en_US
dc.identifier.trdizinid1200676en_US
dc.identifier.urihttps://doi.org/10.30939/ijastech..1278573
dc.identifier.urihttps://search.trdizin.gov.tr/tr/yayin/detay/1200676
dc.identifier.urihttps://hdl.handle.net/20.500.12684/14665
dc.identifier.volume7en_US
dc.indekslendigikaynakScopusen_US
dc.indekslendigikaynakTR-Dizinen_US
dc.language.isoenen_US
dc.publisherSociety of Automotive Engineers Turkeyen_US
dc.relation.ispartofInternational Journal of Automotive Science and Technologyen_US
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanıen_US
dc.rightsinfo:eu-repo/semantics/openAccessen_US
dc.subjectConical die deep drawingen_US
dc.subjectDeep drawing ratioen_US
dc.subjectDP800en_US
dc.subjectMART1200en_US
dc.titleAssessment of Conical Die Deep Drawability of DP800 and MART1400 Advanced High Strength Steelsen_US
dc.typeArticleen_US

Dosyalar

Orijinal paket
Listeleniyor 1 - 1 / 1
Küçük Resim
İsim:
14655.pdf
Boyut:
1.31 MB
Biçim:
Adobe Portable Document Format
İndir

Koleksiyon

Scopus İndeksli Yayınlar Koleksiyonu
TR-Dizin İndeksli Yayınlar Koleksiyonu