Influence of Processing Parameters on the Surface Roughness of Solid Wood Cut by Abrasive Water Jet

Basit Öğe Kaydı
dc.contributor.authorPelit, Hüseyin
dc.contributor.authorYaman, Ozkan
dc.date.accessioned2021-12-01T18:47:40Z
dc.date.available2021-12-01T18:47:40Z
dc.date.issued2020
dc.department[Belirlenecek]en_US
dc.description.abstractThe surface roughness of pine, beech, and oak wood cut in the abrasive water jet (AWJ) system was evaluated for different processing parameters. Wood specimens were prepared in thicknesses of 18, 36, and 54 mm in both tangential and radial directions. Then the specimens were cut, applying three different feed speeds (50, 100, and 200 mm/min), three different abrasive flow rates (200, 300, and 450 g/min), and two different cutting liquid pressures (300 and 380 MPa) with the AWJ system. The R-a and R-Z roughness values were higher in the tangential cut for pine and oak specimens and in the radial cut for beech wood. Roughness values increased in all specimens with increases in the AWJ feed speed and the wood thickness. In contrast, with increased amounts of abrasive, R-a and R-Z values of the specimens decreased and surface smoothness tended to increase. Roughness values of pine and oak specimens generally decreased due to the increase in liquid pressure. However, an increase in the roughness of the beech specimens was determined. As a result, the feed speed and wood thickness were the most influential parameters on the roughness of specimens. In contrast, the cutting direction and liquid pressure showed less importance on the roughness.en_US
dc.description.sponsorshipResearch Fund of Duzce UniversityDuzce University [BAP-2017.07.01.521]en_US
dc.description.sponsorshipThe authors are grateful for the support of the Research Fund of Duzce University, Grant No. BAP-2017.07.01.521.en_US
dc.identifier.doi10.15376/biores.15.3.6135-6148
dc.identifier.endpage6148en_US
dc.identifier.issn1930-2126
dc.identifier.issue3en_US
dc.identifier.scopus2-s2.0-85088451935en_US
dc.identifier.scopusqualityQ3en_US
dc.identifier.startpage6135en_US
dc.identifier.urihttps://doi.org/10.15376/biores.15.3.6135-6148
dc.identifier.urihttps://hdl.handle.net/20.500.12684/10340
dc.identifier.volume15en_US
dc.identifier.wosWOS:000555791100006en_US
dc.identifier.wosqualityQ2en_US
dc.indekslendigikaynakWeb of Scienceen_US
dc.indekslendigikaynakScopusen_US
dc.language.isoenen_US
dc.publisherNorth Carolina State Univ Dept Wood & Paper Scien_US
dc.relation.ispartofBioresourcesen_US
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanıen_US
dc.rightsinfo:eu-repo/semantics/openAccessen_US
dc.subjectAbrasive water jeten_US
dc.subjectProcessing parameteren_US
dc.subjectSurface roughnessen_US
dc.subjectWood materialen_US
dc.subjectChosen Parametersen_US
dc.subjectBonding Strengthen_US
dc.subjectFeed Rateen_US
dc.subjectOptimizationen_US
dc.subjectPressureen_US
dc.subjectTopographyen_US
dc.subjectSpeeden_US
dc.subjectAngleen_US
dc.subjectOaken_US
dc.titleInfluence of Processing Parameters on the Surface Roughness of Solid Wood Cut by Abrasive Water Jeten_US
dc.typeArticleen_US

Dosyalar

Orijinal paket
Listeleniyor 1 - 1 / 1
Küçük Resim
İsim:
10340.pdf
Boyut:
443.64 KB
Biçim:
Adobe Portable Document Format
Açıklama:
Tam Metin / Full Text
İndir

Koleksiyon

WoS İndeksli Yayınlar Koleksiyonu
Scopus İndeksli Yayınlar Koleksiyonu