Optimization of Production Parameters of Densified Laminated Veneer Lumber Produced by Using Urea-Formaldehyde Resin

Basit Öğe Kaydı
dc.authoridOnat, Saadettin Murat/0000-0003-1749-0619en_US
dc.authorscopusid26644434600en_US
dc.authorscopusid56242605200en_US
dc.authorwosidÖzdemir, Serkan/JAZ-1331-2023en_US
dc.authorwosidOnat, Saadettin Murat/P-8696-2019en_US
dc.contributor.authorOnat, Saadettin Murat
dc.contributor.authorOzdemir, Serkan
dc.date.accessioned2024-08-23T16:03:23Z
dc.date.available2024-08-23T16:03:23Z
dc.date.issued2023en_US
dc.departmentDüzce Üniversitesien_US
dc.description.abstractThis research aims to optimize densified laminated veneer lumber production parameters of compression ratio, press temperature, press time, and adhesive spread rate to maximize their mechanical properties. In the manufacturing process of densified laminated veneer lumber, I-77/51 American poplar clone (Populus deltoides) veneers and urea formaldehyde adhesive are used. The results showed that the compression rate and press time had the most significant impact on the mechanical properties of densified laminated veneer lumber. The optimal production conditions were determined as follows: 38 % compression, press temperature of 170 degrees C, press time of (10 +/- 3) minutes, and spread rate of 150 g/m2. Modulus of rupture, modulus of elasticity, tensile shear strength, and tensile strength perpendicular to panels surface of densified laminated veneer lumbers produced under these conditions increased by 49 %, 8 %, 71 %, and 23 %, respectively, compared to the control group of laminated veneer lumber. So, it can be said that the production parameters of densified laminated veneer lumbers can be optimized safely and effectively using Taguchi method-based grey relational analysis.en_US
dc.identifier.doi10.5552/drvind.2023.0079
dc.identifier.endpage335en_US
dc.identifier.issn0012-6772
dc.identifier.issn1847-1153
dc.identifier.issue3en_US
dc.identifier.scopus2-s2.0-85173807924en_US
dc.identifier.scopusqualityQ2en_US
dc.identifier.startpage327en_US
dc.identifier.urihttps://doi.org/10.5552/drvind.2023.0079
dc.identifier.urihttps://hdl.handle.net/20.500.12684/13722
dc.identifier.volume74en_US
dc.identifier.wosWOS:001137987100010en_US
dc.identifier.wosqualityQ4en_US
dc.indekslendigikaynakWeb of Scienceen_US
dc.indekslendigikaynakScopusen_US
dc.language.isoenen_US
dc.publisherZagreb Univ, Fac Forestryen_US
dc.relation.ispartofDrvna Industrijaen_US
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanıen_US
dc.rightsinfo:eu-repo/semantics/openAccessen_US
dc.subjectdensificationen_US
dc.subjectlaminated veneer lumberen_US
dc.subjecturea formaldehydeen_US
dc.subjectprocessing parametersen_US
dc.subjectTaguchi method based grey relational analysisen_US
dc.subjectMechanical-Propertiesen_US
dc.subjectDensificationen_US
dc.subjectStrengthen_US
dc.subjectDensityen_US
dc.subjectPlywooden_US
dc.subjectRecoveryen_US
dc.titleOptimization of Production Parameters of Densified Laminated Veneer Lumber Produced by Using Urea-Formaldehyde Resinen_US
dc.typeArticleen_US

Dosyalar

Koleksiyon

WoS İndeksli Yayınlar Koleksiyonu
Scopus İndeksli Yayınlar Koleksiyonu