Experimental and Statistical Investigation of Machinability of AISI D2 Steel Using Electroerosion Machining Method in Different Machining Parameters

Basit Öğe Kaydı
dc.contributor.authorNas, Engin
dc.contributor.authorOzbek, Onur
dc.contributor.authorBayraktar, Furgan
dc.contributor.authorKara, Fuat
dc.date.accessioned2021-12-01T18:47:30Z
dc.date.available2021-12-01T18:47:30Z
dc.date.issued2021
dc.department[Belirlenecek]en_US
dc.description.abstractThis study investigated the effects of machining parameters on the experimental and statistical results using the electric discharge method in the machining of AISI D2 cold work tool steel. The design of the experiment was established using the Taguchi L-18 method. The effect of the experiment parameters on the performance characteristics was analyzed by analysis of variance (ANOVA). As a result of the study, it was determined that increasing amperage and pulse time affected the surface roughness and hole diameter on the surface of the material. The lowest values for surface roughness, machining time, hole diameter, and crater diameter were determined as 2.085 mu m, 47 minutes, 12.010 mm, and 81.007 mu m, respectively. The highest wear amount was obtained as 0.604 grams with the processed parameters in the ninth experiment. When the signal-to-noise ratios were examined, the optimum combinations of the control factors for surface roughness, hole diameter, crater diameter, wear amount, wear rate, and processing time were determined as A(1)B(1)C(3), A(1)B(1)C(3), A(1)B(1)C(3), A(1)B(3)C(1), A(2)B(1)C(1), and A(1)B(3)C(3), respectively. According to the ANOVA results, the most important parameters affecting the test results for surface roughness, hole diameter, crater diameter, wear amount, material wear loss, and processing time were determined as amperage (49.34%), time-on (59.38%), amperage (55.65%), time-on (56.92%), amperage (51.42%), and amperage (78.02%), respectively. When the gray relational degree was calculated for the maximum and minimum values, the ideal factors for all output results were found to be the parameters applied in the third experiment.</p>en_US
dc.identifier.doi10.1155/2021/1241797
dc.identifier.issn1687-8434
dc.identifier.issn1687-8442
dc.identifier.scopus2-s2.0-85118542095en_US
dc.identifier.scopusqualityQ2en_US
dc.identifier.urihttps://doi.org/10.1155/2021/1241797
dc.identifier.urihttps://hdl.handle.net/20.500.12684/10293
dc.identifier.volume2021en_US
dc.identifier.wosWOS:000715783100001en_US
dc.identifier.wosqualityQ3en_US
dc.indekslendigikaynakWeb of Scienceen_US
dc.indekslendigikaynakScopusen_US
dc.language.isoenen_US
dc.publisherHindawi Ltden_US
dc.relation.ispartofAdvances In Materials Science And Engineeringen_US
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanıen_US
dc.rightsinfo:eu-repo/semantics/closedAccessen_US
dc.subjectSurface-Roughnessen_US
dc.subjectCutting Parametersen_US
dc.subjectResidual-Stressen_US
dc.subjectTaguchi Methoden_US
dc.subjectTool Steelen_US
dc.subjectOptimizationen_US
dc.subjectElectrodesen_US
dc.titleExperimental and Statistical Investigation of Machinability of AISI D2 Steel Using Electroerosion Machining Method in Different Machining Parametersen_US
dc.typeArticleen_US

Dosyalar

Orijinal paket
Listeleniyor 1 - 1 / 1
Küçük Resim Yok
İsim:
10293.pdf
Boyut:
8.25 MB
Biçim:
Adobe Portable Document Format
Açıklama:
Tam Metin / Full Text
İndir

Koleksiyon

WoS İndeksli Yayınlar Koleksiyonu
Scopus İndeksli Yayınlar Koleksiyonu